Nite-Tek T20's

[Radagast]

G'day Tom, you need to put your location in your profile, Its a forum rule. Otherwise the Moderator Mafia will come in the night and put a dead badger in your bed.

[Marky610]

Can the 3 mode be set say on min like some using memory??

Unfortunately not, the drivers have no memory, they always fire up on high. My recommendation will be to switch it on pointing in the sky then two half presses to change to low before pointing at the floor. They would be better too if starting low and getting brighter but they do the exact opposite. I will have words with the Chinese and see if they can change it.

Hi I would love an 850nm one if you have any left.
Thanks
Tom

No worries bud consider it done

[mole trapper]

Hiya Marky, any news on these yet?
Cheers J

News on what? I have torches in stock and the 3 mode drivers will be here this week

Hi Mark, have I not asked nicely enough to receive such a curt reply?
Early in this thread I asked for your advice, you replied that the three mode jobby would be what I needed, I was merely asking how things were progressing.

[Bulls_hitter]

Hi marky
I would like one of these ir torches to use on vehicle mounted pulsar 750 recon i don't know much about ir lamps but if you guide me to the best unit and tell me how to pay. I have a paypal account if this is ok.
I eagerly await your reply
Steve

[Marky610]

Hiya Marky, any news on these yet?
Cheers J

News on what? I have torches in stock and the 3 mode drivers will be here this week

Hi Mark, have I not asked nicely enough to receive such a curt reply?
Early in this thread I asked for your advice, you replied that the three mode jobby would be what I needed, I was merely asking how things were progressing.

Sorry, should have put a 'sorry' at the start of that, I know to you it's personal because you asked me something but please imagine how many questions and request's I get in a day, sometimes I need a little more detail to remind me

[Marky610]

Hi marky
I would like one of these ir torches to use on vehicle mounted pulsar 750 recon i don't know much about ir lamps but if you guide me to the best unit and tell me how to pay. I have a paypal account if this is ok.
I eagerly await your reply
Steve

Although it will do the job I wouldn't recommend a torch for that job, better off with a vehicle supplied lamp than a torch. But it's up to you?

[Marky610]

Check out my new online order form in my signature

[mole trapper]

News on what? I have torches in stock and the 3 mode drivers will be here this week[/quote]
Hi Mark, have I not asked nicely enough to receive such a curt reply?
Early in this thread I asked for your advice, you replied that the three mode jobby would be what I needed, I was merely asking how things were progressing.[/quote]
Sorry, should have put a 'sorry' at the start of that, I know to you it's personal because you asked me something but please imagine how

many questions and request's I get in a day,
sometimes I need a little more detail to
remind me [/quote]
Fair enough Mark.
So just to confirm then, when you are happy with the three mode drivers could you please give me the heads up? Just to nudge your memory, it was for photon and ns50/200 out to no more than hundred yards, for rat and rabbit work, so presumably t20 with 3 driver and a pressure switch, mount?
Cheers Jamie

[Bulls_hitter]

Hi marky
I have just ordered 2 torches and accessories from your contacts page and at checkout it only charged me 3 dollars. I paid the 3 dollars then paid you again £120 for the order via paypal any problems please contact me.
Steve

[Marky610]

Hi marky
I have just ordered 2 torches and accessories from your contacts page and at checkout it only charged me 3 dollars. I paid the 3 dollars then paid you again £120 for the order via paypal any problems please contact me.
Steve

Thanks for being my guinea pig, it's not easy setting these things up